Vista 10p zone programming

Enter the predefined address for this module ; see Table of Device Addresses on page 2. Enter the zone list number to program or 00 to exit this mode.

Make sure these addresses are not used Enter each zone number to add to the zone list, followed by pressing by physical modules that may be installed. Press 00 to continue. The system will then display To delete this output definition, press 1. If you do not want to delete this the descriptor for zone 1. To program custom words, press 1 custom words are described later. Press [ ] plus the 3-digit number from the Alpha Vocabulary List on page 11 for the first word.

Press [6] to accept the word and move the cursor for the next word. Repeat steps 2a and 2b for the second and third words if used. Enter the desired zone type. The flashing cursor disappears. Repeat steps to assign a descriptor for the next zone. Enter 0 no at the prompt to exit this mode and return to Data Field mode. Repeat Step 3 to create the desired word s.

When the word is complete, press the [8] key to save the custom word s [8] saves the new word in the system's memory. Repeat Steps 1—5 for other custom words to be entered. To change a 1. When all words have been programmed, is displayed. Enter the number 01—10, or 11, 12, 13 for partition descriptors— see Alpha prompt. Enter 0 again to exit Descriptor mode. Press [ ], followed by the two-digit entry for the first letter you would like to display e. The cursor moves to the right, in position for the next character.

If using a Phone module, and words other than these are selected for Alpha descriptors, the module will not provide annunciation of those words. Vidya Sutton Dec. RobertMarancik Feb. Marco A Ramos Apr. Total views. You just clipped your first slide! Clipping is a handy way to collect important slides you want to go back to later. Now customize the name of a clipboard to store your clips. Visibility Others can see my Clipboard. Wireless zones can be started at zone 9 or later.

A summary screen will be displayed. Enter the Zone Type ZT. You can refer to the programming guide for a list of available zone types. Most people will only need to use partition 1. If you are on a 15P, skip this step. Installer code followed by to get into programming mode.

This is only used for wireless zones so you can select 0 for the purposes of this tutorial. A summary screen will be displayed. Enter the Zone Type ZT.

Do not install within the control cabinet. Install transmitters in accordance with the instructions provided with each. If at least. At the end of their life, the complete unit must be replaced and a new serial number enrolled by the control. Do not install batteries in wireless transmitters until you are ready to enroll during system programming.

After enrolling, batteries need not be removed. Remove the ohm EOL resistor if connected across the selected zone. Using a standard keypad cable as shown:. Connect a ohm EOL resistor across the momentary switch. You can wire an optional closed-circuit tamper switch model in series with the zone.

If the switchplate is then removed from the wall, the tamper will open, disabling keyswitch operation until the system is next disarmed from the keypad. Mount either remotely or in the control panel. Use standard 4-conductor twisted cable for long wiring runs. Connect the desired field wiring to the unit's relay contact terminals. Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally located above the terminal strip.

U L If on-board triggers are used, the wiring between the control unit and the UL Listed device must be run in conduit, be no more than 3 feet apart and have no intervening barriers or walls.

GND -. Connect incoming phone line and handset wiring to the main terminal block via an RJ31X jack as shown in the Summary of Connections diagram at the back of this manual. Wire colors. Connect Phone Module terminals as shown below. Use an RJ31X jack with a direct-connect cord and make all connections exactly as shown. Compatibility: Phone Modules must have software version WA The wiring diagram shows the wiring connections that will provide proper operation in most cases.

Connection to the incoming telco line via a RJ31X jack and direct-connect cord, as shown, is essential, even if the system is not connected to a central station.

The house phone lines gray and brown wires must be wired to the phone module terminals; not to the control terminals. Otherwise, an error signal fast busy signal will occur when trying to access the system from an on-premises phone. GREY R. Use compatible Long Range Radios e. Refer to the connection diagrams below. You can program the system at any time, even at the installer's premises prior to the actual installation. The following is a list of the various Programming modes used to program this system:.

Keypads are identified by predefined addresses starting at address 16 as follows:. Once a wireless key is enrolled, it must be assigned to a user before it becomes active. System Communication and Operation.

System must be armed for the Latchkey report to be sent. If using a function key to manually send a message to a pager, see Function Keys paragraph on the next page.

You must assign a zone type to each zone, which defines the way in which the system responds to faults in that zone. Zone types are defined below. In the case of a. The system keypad will display.

Allows for a custom zone response. UL installations: Zone Type 90 may not be used as fire or burglar alarm zones on. NOTE: All of the zone types described are available for the wireless portion of the system, if used.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Recommendations For Proper Intrusion Protection For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. Figure 1. Mounting the PC Board Mounting Board with RF Receiver 1.

Swing this board into place and secure it with two additional screws. Mounting and Wiring the Control Wiring to Keypads 1. Supplementary Power optional 1. Using a Supplementary Power Supply no. Installation Instructions Sounder Bell Connections 1.

For supervised output, continue with steps 2 and 3.