Install coaxial wall plate

Position the low-voltage mounting plate against the cutout on the wall. Bend the two metal tabs on the inside of the low-voltage mounting plate into the wall.

Continue to the bend the tabs until they clamp onto the drywall. The mounting plate acts as a bracket and has screw holes for the coaxial wall plate. Twist the connector for the end of the coaxial cable to the back of the connector on the coaxial wall plate. Place the wall plate against the wall and over the low-voltage mounting plate.

Use the screws that came with the coaxial wall plate to attach it to the mounting plate. Connect the end of a length of coaxial cable to the connector on the outside of the wall plate. Connect the other end of the coaxial to your television or receiver. Cecilia Harsch has been writing professionally since She writes mainly home improvement, health and travel articles for various online publications.

The keyhole saw should be used to cut through the drywall to make the aperture necessary for the installation of a low voltage electrical box. First and foremost, ensure that the area you want to drill into is free of any potential dangers before proceeding to the following step i.

Place the tip of the auger bit into the cutout in the wall and drill through the bottom of the stud wall to obtain access to the crawlspace below while the wall is still open. This will make it much easier to identify the location where the cable will be installed.

Once the cable line is in place, connect one end of the cable line to the tip of the drill bit using a utility string before returning to the house. Slowly draw the drill bit and the cable line that has been connected to the drill bit back up through the hole. Slide the low voltage box into the drywall hole and tighten it down to prevent it from moving around throughout the installation process. It is necessary to add an F-connector to the end of the wire before you can complete this portion of the installation.

Install the F-connector on the back of the coax cable receptacle wall plate and screw the wall plate into the low voltage electrical box to complete the installation. If your house was built differently than others, and if your cable lines were installed in a different location than others, the following step may be different for you.

Now that one end of the cable line has been placed, you may use cable clips to attach the remaining length of wire to the floor joists as you work your way closer and closer to the hole you just created, which is closest to the cable box. A short piece of string should be tied to the end of the fish pole after you have arrived to the drilled hole. A short piece of string should be tied to the end of the fish pole after you have arrived at the drilled hole. It is necessary to attach an F-connector to this end of the cable before you can proceed to the next step of the installation.

At the time of installation of a new cable line, I label it with a paint marker so that if an emergency occurs and I need to disconnect my connections, I can be confident that the right cables are reconnected. The last step is to connect your freshly installed cable line to an open connection on the cable splitter provided by the cable provider. In the event that you lay a spool of cable on its side and begin pulling the cable off of it , the cable will twist as it unravels, and when you pull on the twisted cable, the cable kinks.

A piece of conduit should be threaded through the middle of the spool and resting on a ladder is the ideal method. A spare piece of wire is used to hold the conduit in place. If you imagine wrapping a cable around a coffee can, you will understand why coaxial wire should never be twisted more sharply than that.

When a severe bend is inevitable, such as behind a television stand, a degree adaptor should be used. The foil should be left in place once the coaxial cable has been removed; however, peel out the braid.

A utility knife may be used to strip a coaxial wire, and it is not difficult, but it is not simple either. Strippers for coaxial cables feature two blades: one blade cuts through the jacket without harming the braid, while the second blade cuts through everything else, except for the central conductor, of the cable.

This allows for the same amount of signal to reach the Antenna on a longer run of Cable verses a shorter run of Cable. Coax splitters are used to split a CATV signal so that it can be used for more than one device.

They are a simple plug and play device that can be installed in minutes. This 2 - way splitter supports frequencies from 5 to MHz. Use a splitter with as few connections as possible two way splitters will typically have the least signal loss. Try not to daisy chain splitters splitter attached to a splitter. If you need more ports, a four-way splitter is better than 3 two -way splitters.

Longer runs of coaxial cable have larger signal loss. To test a splitter for through loss, first measure and record the level of the signal source. Next terminate all but one of the output terminals of the splitter with a 75 ohm resistor. Measure the signal level at the unterminated output port with the Frequency Selective Voltmeter.

Ethernet is just plain faster than Wi-Fi—there's no getting around that fact. The exact maximum speed of your Ethernet cable depends on the type of Ethernet cable you're using. While it's perfectly reasonable to install ethernet cabling around a home, an alternative is "powerline ethernet ", which runs a network signal through your power cables.

An electrician can wire your house up with Ethernet jacks but that doesn't mean they're going to go anywhere other than a wiring closet. Run the cable back to your primary Ethernet port, drilling holes as needed to pass it through the floor or through walls and stapling it to wall or floor joists as necessary with wire staples.

Plug the male end of the cable into your Internet modem or whichever device is serving as your main hub. To convert a phone jack into an Ethernet jack that can be connected to a computer, install a DSL modem using the telephone jack in your home. A few supplies from an electronics shop are needed. Place the DSL modem next to the computer that will be used to access the Internet.

If both cables are the same price per spool, go with cat6. If cat5e is cheaper and you want something easier to work with and you only plan on going gigabit, go with cat5e.

If you plan on going 10 gig in the future and all runs are under 50 meters, go with cat6. If you have a male socket you will need either a cable with a female plug fitted to it or a male plug with a coaxial coupler fitted into it.

This will provide you with a female connection.